Türksat Frequency Settings: Fix Missing Channels on 42° East (Step-by-Step)
Independent guide — no official affiliation with the platforms mentioned.
إجابة قصيرة
If channels are missing on Türksat 42° East, select the 42° East satellite in your receiver, verify signal quality, then run a blind/automatic scan. The TRT package broadcasts on 12380 H 27500; national commercial channels use 11958 V 27500 and 12015 H 27500. Frequencies change occasionally — a re-scan recovers them without manual entry.
المصدر الرسمي
turksat.com.tr
Güncel frekans listesi Türksat'ın kendi duyurusudur
01 — إصلاح خطوة بخطوة
إصلاح خطوة بخطوة
STEP 01
Select 42° East in the satellite list
Open Menu > Installation > Satellite Settings on your receiver and choose 'Türksat 42° East' as the scan target. Other satellites in the list (7°, 16°, 26°…) do not carry Turkish national channels; scanning the wrong satellite returns nothing.
STEP 02
Check signal strength and quality
Watch the Strength and Quality bars on the same screen. Quality should sit above 60%. If the bar stays empty, the LNB cable may be loose: reseat the connector at the dish arm and at the receiver's tuner input.
If signal died completely after a thunderstorm, a burnt LNB is the most common cause — the quality bar stays at 0 even though settings are untouched.
STEP 03
Run the automatic (blind) scan
Go to Menu > Channel Search > Automatic Scan and pick 'Blind Scan' or 'Full Network Scan'. The scan takes 5-15 minutes; do not power off the receiver. This finds channels whose frequencies changed without any manual entry.
STEP 04
Add a transponder manually (one package missing)
If only one package is missing, open Channel Search > Manual (TP) and enter the missing row: 12380 H 27500 (TRT package), 11958 V 27500 (national commercial package), 12015 H 27500 (national commercial package). Match polarization and symbol rate exactly, then start the scan.
Frequencies change by operator announcement. Values above are the widely verified transponders as of September 2026; check the official Türksat announcements page for the current list.
STEP 05
Sort and save the channel list
After the scan finishes, confirm 'Save List'. Channels arrive in frequency order: enable 'LCN / Channel Number' sorting in List > Sort so channels align to the broadcaster's official numbers (TRT 1 = 1, Show TV = 3, etc.).
نصائح
- Try a blind scan before a factory reset — the reset also wipes satellite and LNB settings and forces full re-installation.
- Picture freezing during heavy rain is rain fade on a marginal signal, not a misaligned dish. Shielding the dish from direct wind reduces winter dropouts.
- Second-hand receivers often ship with shop-loaded lists. Enable LCN after scanning to restore the official channel numbering.
02 — أسئلة شائعة
أسئلة شائعة
Why do Türksat frequencies keep changing?
Broadcasters move transponders when satellite capacity is replanned. That is why a blind scan beats hunting frequencies online: it walks every transponder and discovers the new address by itself.
Which frequency carries TRT 1?
The TRT package sits on Türksat 42° East at 12380 MHz, horizontal (H) polarization, 27500 symbol rate, broadcast as DVB-S2/MPEG-4. Setting vertical (V) polarization yields zero quality.
Signal quality is fine but the channel list is empty — why?
A full quality bar proves the dish and LNB are healthy; the channel list itself was reset (factory reset or a new receiver). Running the automatic scan above rebuilds the list.
هل حل هذا الدليل المشكلة؟
ملاحظاتك تحسن دليلاتنا — يستغرق 10 ثوانٍ فقط.
الروابط في هذا الدليل تشير إلى صفحات المنصة الرسمية. قد تتغير الخطوات مع تحديثات المنصة؛ تحقق من تاريخ الصفحة.
03 — دلائل ذات صلة